Telemetry Dashboard for Scania G & R & T v 08

Sponsored links

INSTALLATION:
• Extract the contents of the RAR archive. LEAVE THE “SCANIA G-R-T” FOLDER INTACT.
• Move the “Scania G-R-T” Folder to the Skins folder of the Telemetry Server (located at *SERVER-ROOT-FOLDER*Htmlskins)
• Go bonkers! BUT NOT BEFORE AT LEAST BRIEFING THROUGH THE REST OF THE README.

BRIEF DOCUMENTATION:
The dashboard computer has 3 information displays that stay exactly where they are, as long as the truck’s battery is running:
• At the very top of the dashboard computer, on the left is displayed the gear currently selected, and on the right is the game time in format HH:MM. If and when you engage the Engine Brake, the corresponding Engine Brake icon will appear just to the left of the time display, and vice versa.

• Just below the Gear&Time row, there is the Speeds Information display:
– on the very left is the actual truck speed (km/h)
– to its right is the Cruise Control Downhill Tolerance range (fixed at 5km/h due to the Telemetry’s incapability of reading the Cruise Control Step Grid from the game; however, it WILL light up as soon as Cruise Control is engaged)
– on the right-hand side of the Speeds Info display, is the Cruise Control setting currently selected in the simulator (fully operable).

• At the bottom sector of the dashboard display:
– In the upper part of the bottom sector, there is the estimated distance from the truck’s current position to the GPS destination (in kilometers).
– Above the truck symbol, the mass of the trailer currently attached to the truck is displayed (if there is one).
– In the bottom part of the bottom sector, is the Odometer – displays the distance driven with the particular truck selected in the simulator.

The dashboard computer added to this skin has 4 pages of information, displayed in the middle of the dashboard computer screen, between the Speed Info display and the Distance&Odometer. IN ORDER TO CYCLE BETWEEN THE PAGES, SIMPLY CLICK ANYWHERE ON THE DASHBOARD COMPUTER. Below are listed the pages, with a short description of the data found in each one of them, from the highest to the lowest:
• Page I – Fuel Page: at the top of the the page, there is the current amount of fuel loaded into the truck, in litres. Right below it is a bar displaying how much of the fuel tank is loaded (visual fraction). Below that bar, is the Average Fuel Consumption (in Litres per 100km) in green, below which there is the estimated distance the fuel will be enough for (don’t confuse with the Distance-to-Destination right below it), in green as well.

• Page II – Air Pressure Page: all three bars read the same measurement – Air Pressure (in the tank), in PSI (useful only with “Air Brakes Simulation” enabled in the game); the game does not distinguish between different Air Pressures in the different air tanks.

• Page III – Diagnostics Page: the number at the top (in white) denotes the current Water Temperature (in Celsius degrees), and right below it is a bar displaying the same datum. Below those two is the Oil Temperature (in Celsius degrees), and the Oil Temperature in a bar-format display.

• Page IV – Truck Statistics Page: the top bar displays the current brake pedal pressure (how hard it’s pressed down, which gives a pretty good idea about the Brake Pad pressure, although no such datum is available through the Telemetry SDK); quite visually-self-explanatory. The bar in the middle displays the Brake Temperature in Celsius degrees. The bottom one displays the truck’s Battery Voltage, in Volts.

Other additional features:
• Added the retarder icon to the dashboard; when the retarder is engaged, the icon (green) will appear below the Speedometer.
• IF THE DASHBOARD SEEMS TO BE TURNED OFF – I have re-programmed the entire the dashboard so as to make its Meters read their minimal value, make the warning lights extinguish, and make the dashboard computer itself turn off, WHENVER THE BATTERY IS OFF. In most cases, the dashboard will look like that also when the Telemetry Server is not connected to Euro Truck Simulator 2.

IN CASE YOUR TRUCK IS UP AND RUNNING, AND THE TELEMETRY SERVER INDICATES THAT IT’S CONNECTED TO THE SIMULATOR, OR IF YOU HAVE ANY OTHER PROBLEM THAT YOU SUSPECT IS A BUG IN THE DASHBOARD – PLEASE CONTACT ME ON THE FOLLOWING E-MAIL ADDRESS: [email protected] .

Needless to say, I DO NOT PERMIT, AGREE, OR GIVE MY CONSENT, TO ANY RE-PUBLISHING OR DISTRIBUTION OF THIS DASHBOARD SKIN, ON ANY PLATFORM OR IN ANY OTHER WEBSITE, except for Funbit, the distributor of this package as part of the entire Telemetry SDK.

Enjoy the dashboard!

Credits:
Nazgûl

DOWNLOAD 2 MB

9 thoughts on “Telemetry Dashboard for Scania G & R & T v 08

  1. nicely done, especially considering telemetry limitations.
    reminds me of the telemetry web server and dashboard by Funbit, which is universal but has a different function set

  2. обычный мод нельзя что ли сделать простой долбаный мод и все.

  3. Where is situated the file(case) to put this mod? I do not understand well.

  4. Folder to the Skins folder of the Telemetry Server (located at *SERVER-ROOT-FOLDER*Htmlskins) ????????
    Sorry

  5. Works with RJL Scania ?

  6. As a person who is not into modding at all, finding that installation folder is harder as it may sound… Perhaps a more detailed instruction could help?

  7. Is this for the ETS2 Telemetry Web Server? Moron!

  8. Remif9428

    Why is there no speed gauge ?

  9. the speed gauge not operate. What i have to do to fix it ?

Leave a Reply to kolynrae Cancel reply

Your email address will not be published.